Skip to main content

NINGBO YUANJING AUTOMOTIVE PARTS CO., LTD. — brake pad backing plates and custom metal stamping parts

Rows of steel brake pad backing plates on a brushed metal surface, fading into a blue gradient

Model discovery

Backing Plates Identified by the Numbers Buyers Use

Search by FMSI, OE, WVA or TRW reference and open the dimensions, material and fitment for each steel substrate.

Model finder

Start with the number on your list

Search FMSI, OE, WVA and TRW references or a vehicle name. Select up to three models to compare dimensions and fitment side by side.

5 models shown

  • D1344-8455 steel brake pad backing plate with four round holes and a small locating ear on each end

    D1344-8455

    Q235B · 145.4 × 56.9 mm

  • D1044-7947 steel brake pad backing plate with two large holes, three raised pins and stepped shoulders

    D1044-7947

    Q235B · 155.1/156.3 × 62.4/67 mm

  • Pair of D976 steel brake pad backing plates, each with two large holes, a curved upper notch and small lower holes

    D976

    Q235B · 134.6 × 77.1 mm

  • D2017 steel brake pad backing plate with a long curved profile, two center holes and four raised pins

    D2017

    Q235B · 167.2 × 54.3 mm

  • D1295 steel brake pad backing plate with four large holes, two raised pins and a locating ear on each end

    D1295

    Q235B · 137.8 × 61 mm

Applications

Vehicle families the launch range fits

Each family links straight to the backing plate model listed for it. Check the model page for the exact fitment and reference numbers.

Structural support

A thin plate that has to sit true

The backing plate carries the friction material and passes caliper force across the pad. Outline, hole positions and ear geometry decide whether it seats in the bracket, so dimensional control starts with the tool.

Overall length and height

Blue guides mark the spans that decide whether a plate seats in the caliper bracket: overall length across the ears and overall height at the arc.

This model is a teaching illustration. It does not represent an exact customer product, machine or measured result.

Manufacturing

From sheet steel to finished goods, under one roof

  1. Entrance of Building 24 with a brass nameplate, opening onto a press hall with a forklift and baskets of stamped plates
    Facility entrance, Building 24 · Representative facility photography

    Step 01

    One 3,000 m² facility, three production lines

    Building 24 at Yida Science and Innovation City holds three production lines, with separate areas for automatic blanking, molds, packaging, shot blasting, quality inspection and finished goods.

  2. Automatic feeding rails carrying a large steel sheet into a press for blanking
    Automatic blanking line · Representative facility photography

    Step 02

    Automatic blanking from sheet steel

    Steel sheet is fed to the press on an automatic blanking line, cutting plate outlines in a repeatable first operation.

  3. Press hall with a red hydraulic shear in the foreground, a green feeding frame and a press behind it
    Press hall · Representative facility photography

    Step 03

    Hydraulic and high-precision presses

    Two 200-ton hydraulic presses and five 160-ton high-precision presses sit alongside ten presses across 16, 40, 80, 125 and 160 tons, so tonnage can follow the part.

  4. Blanked backing plates travelling on a patterned belt through a deburring machine
    Deburring machine · Representative facility photography

    Step 04

    Deburring before the next operation

    Two deburring machines clean blanked edges. Plates run across the belt and leave ready for hole and edge operations.

  5. Close view of automatic processing equipment with a servo motor, cylinders and guide rails
    Automatic processing equipment · Representative facility photography

    Step 05

    Automatic punching and chamfering

    Two automatic punching systems and one automatic chamfering system handle hole and edge operations without hand feeding each plate.

  6. Wire basket holding finished backing plates beside a finishing machine
    Finishing and handling · Representative facility photography

    Step 06

    Shot blasting and finished goods

    One shot-blasting machine prepares the surface. Finished plates move in baskets toward quality inspection, packaging and the finished-goods area.

Established in Ningbo
2017
Production facility
3,000 m²
Production lines
3
Pieces per month, stated capacity
1,000,000
Backing-plate molds
1,000+

Tooling and OEM/ODM

Your drawing becomes a mold, then a repeat part

More than 1,000 backing-plate molds already exist. If your part is not among them, we develop tooling from your drawing.

  1. 01

    Drawing or sample review

    Send a drawing, a sample or a reference number. Outline, hole layout and material are confirmed before tooling starts.

  2. 02

    Mold development

    Tooling is developed from your drawing, supported by an existing library of more than 1,000 backing-plate molds.

  3. 03

    Sampling

    Sample plates are produced from the new mold so fit and dimensions can be reviewed before production.

  4. 04

    OEM / ODM production

    Approved parts move to repeat production on the three production lines, then to packaging and the finished-goods area.

Quality

A dedicated inspection area, and reports on request

Quality inspection has its own area on the production floor, between finishing and the finished-goods area. Tell us which dimensions or documents you need and we will confirm what can be provided with your samples or order.

  • Inspection areaSeparate quality-inspection zone in the facility
  • Dimension checksSpecify the dimensions you want reported
  • ReportsAvailable on request with a quote or sample
  • Quality systemOperated under ISO 9001 quality management

Delivery

Plan your first order with clear numbers

Sampling
Before productionNew tooling is sampled so fit and dimensions can be reviewed first.
MOQ
200 pcsListed on four of the five launch models. D1044-7947 is confirmed in the quote.
Lead time
Typically 15–25 daysDepends on quantity and process. The date for your order is confirmed in the quote.
Capacity
1,000,000 pcs / monthStated monthly capacity across three production lines.

Company

A Ningbo stamping plant focused on backing plates

NINGBO YUANJING AUTOMOTIVE PARTS CO., LTD. was established in 2017 in Ningbo, China. It manufactures automotive brake pad backing plates and custom metal stamping parts.

Address
Building 24, Yida Science and Innovation City, Binhai Development Zone, Chunhu, Fenghua, Ningbo, Zhejiang, China

Request a quote

Send a model number or a drawing

We reply by email. No prices are shown online; each quote is prepared for your quantity and specification.

FMSI, OE, WVA or TRW number, or a short description.

Pieces per order, if known.

Loading…

Quotes are prepared by our team. This form does not take payment.